Machining centres universal – CMS Machining Center 3 axes

Produsent

Maskinnr.

Beskrivelse

Weight: k.A
Control: CNC-OSAI Type 8600MC Fast AT90
Axis travel: X=3600   Y=1600   Z=400
Table top ß e: 2520 x 1260 mm each
Spindle: 3x   8 KW
Tool change: 3 x 12 pcs
Machine Description
TYP NC-PF 3116-3T-CU  
Table dimensions 2 x 2520 x 1260 mm
Cantilevered portal.
  On the front of each table, the following information is provided:-Vacuum: 6 pcs. Each equipped with a hand valve, connected directly to a vacuum pump, and only for manual valve.-Compressed air: 2 pcs. Quick coupling (standard size), loading with separate M-Coden for on / off per table, compressed air on / off -- Switch to the control panel
X-axis hub = 3.600 mmY-axis stroke   = 1,600 mmZ-axis stroke     = 400 mm
from 0-20.000 mm / min programmable working device of the X and Y-axis
from 0-6000 mm / min.Speed on the Z -- Achse.mm / min.
The movement of the axles is carried out by means of motors which are free of rust.
Servo controls of the Simodriive type from Siemens.
Numerical control CNC-OSAI AB, type 8600 MC FAST AT 90Main features:-CNC continuous control with microprocessors for work centres; high program throughput speed (FAST);   with integrated PLC-integratable system::. Main unit (computer)-switchboard -- memory with semiconductors with a capacity of 512 Kb-display of all working data (programs, messages, diagnosis, positons, etc. and large possibilities of handling for test cycles, reference points, feed rate, etc.-Graphic display for program test m i t stationary axes-interpolation optionally on 5 axes-5 simultaneous axes with linear interpolation-2 simultaneous axes with circular interpolation + 3 linear axes-input and output pitch: 0.001 mm.- Meter data pre-plugging-Measurement system: Incremental transductors-Programming with polar coordinates-Profile programming with vector alignment of the Fr ä ser or tool gradient-Standard fixed cycles and deep drilling cycles-Geometric programming of high Nineau (GTL)-Parametric programming (at the same time for processing)-of keyboard (with capability for optimization)-from computer with two universal intermediate circuits RS 232 C (v. 24)   (one output) and 20 mA in current ring point to point -- protocol connection MINI -- DNC for r Endtransfer-Reverse clearance compensation for each axle alignment v. Screw-action-error-controlled acceleration and deceleration on all axes in   Circular interpolation and quick feed-10 zero-step points freely programmable mirror function of the route input rotation of the interpolation-level-scanning-cyklerSplit-axis for gantry (unhaengige / syncronized axes) safety routine always confirmed for measurement kririss,, Ü berhitze, SpannungMemory, Endhub and Werkst ü ckprofil.Die Numerische Controller is on A mobile frame of mounted PCEs can be manually controlled on the entire surface of a plant by a manually controlled system. The data is then automatically collected. A hand route facilitates the positioning of each axle. The PC can store this data and pass it on to the CNC controller as required, or from CNC received main features of PCAT 90microprocessor INTEL 80286, mathematical cooprocessor INTEL 80287-RAM 1044 KbDisk. -- Drive 3.5 " Hard disk 20 MBColor monitor 1 on full keyboard (96 keys) Operating System MS-DOSTeach-In f ü r all axes  
Separate dust-proof switch cabinet complete with air conditioning for the limitation of the internal temperature to approx. 35 degrees; within this cabinet, which lies on the right side of the machine, all electrical and electronic components for the machine control are displayed. Protection level :: IP5
In the switchgear cabinet, the following additional operating conditions are provided:-Vacuum pump 1to the pressure probe of the electrical control cabinet-Vacuum pump 2-Fr ä saggregate 3 Stk., for each motor separately (connected to the program)
3 pcs.; machining units complete with special electric spindle with a sturdy shaft mounted on two prestressed pairs of bearings, suitable for high speeds and performance. Electrospindles of compact structure, all individual parts ground and the rotating parts also dynamically balanced. Power of the electric spindle: 8 kW and 18,000 rpm. (Constant torque)
The units are complete with an automatic tool changing device with 12 stations, which are attached to the unit on its own slide. The rotation of the tool holder is controlled by the CNC.
Tool holder shaft ISO 30 for tools with a cylindrical shaft with a max. Diameter of 25 mm.
The tool magazine is designed for protection against dust and dust with a cover. This ensures the protection of the unit both in operation and at standstill. Fixer distance between the units: 750 mm.All electric spindles can be rotated in a controlled manner by the CNC, in the clockwise direction or in counterclockwise direction.
3 static frequency converters with freely programmable speed ranges between 1,000 and 18,000 revolutions with motor braking and the ability to reverse the speed direction power 11 KW per pcs
Tensioning device from an NC axis (4). Axis) controlled to block a maximum of three parts. The device is fastened on aluminium plate and can be positioned on the left machining table as required. The distance of the parts corresponds to the distance of the units Werkst l ä nge: 200-1000 mm
Fully automatic central lubrication with forced injection to lubricate the sled, provided with pressure and minimum level control imBeh lter.Double vacuum vacuum pump, each 140 cbm
New price of the machine at the time of delivery € 345.000, --

(technical data subject to reservation, as information from the manufacturer)

Keep in mind that the advertisement was translated automatically and may have errors. We are not responsible for these errors.

Delens tilstand

Byggeår

Maskin under kraft